OPTIPOW 105 / V1617803

November 18, 2026

Why does a baghouse lose its cleaning pulse — and what does the OPTIPOW 105 (V1617803) have to do with it?

When a pulse-jet baghouse stops cleaning properly, the filter bags are usually inspected first. Often the cause sits upstream, at the valve. This article uses the OPTIPOW 105 plunger pulse solenoid valve (article series V1617803) as the example: what it does in each cleaning cycle, which limits it is designed to, and what its failure symptoms look like in practice.

OPTIPOW 105 complete valve (Pos. 1) with exploded view: membrane, O-rings, pilot cover, plate, plunger, rubber disc and solenoid valve. Position numbers are used throughout this article to identify each part. Source: manufacturer's parts sheet.


01How does a pulse valve decide whether the bags actually get cleaned?


A pulse-jet collector cleans by firing a short burst of compressed air through a blowpipe into each row of bags. The timer only sends the signal — the valve has to open fast, release the full air volume in one sharp pulse, and close cleanly. The OPTIPOW 105 does this with a plunger (piston) design: the “105” is the piston diameter, 105 mm, and a fast-acting pilot solenoid (Pos. 9) triggers the main stage via the membrane (Pos. 2).

When any link in that chain weakens, the symptoms are consistent — and they appear long before the valve stops working altogether:

  • A soft or drawn-out pulse — dust cake is only partly dislodged, so differential pressure climbs steadily between maintenance windows.

  • Slow opening or a puff of dust after the pulse — the membrane has stiffened or the plunger (Pos. 7) is no longer moving freely.

  • Air bleeding at the vent, or a valve stuck open — sealing surfaces are compromised: membrane (Pos. 2), O-rings (Pos. 3 / 4) or rubber disc (Pos. 8).

  • No response to the signal at all — check the pilot side first: solenoid valve (Pos. 9) and pilot cover (Pos. 5), before assuming the main valve has failed.

02What do the pressure and temperature figures actually mean?

< 6 bar

Operating pressure


50 °C

Max. operating temperature


100 °C

Design temperature


105 mm

Piston diameter (“105”)


Two pairs of figures are often confused. Operating values are the conditions for continuous service: pressure below 6 bar and temperature up to 50 °C. Design values are the envelope the valve is engineered to withstand: a design temperature of 100 °C and, per the manufacturer's data for this valve type, a design static pressure of 15 bar. Running continuously at design values is not the same as running within operating values — if a header regularly sits above 6 bar or the gas stream keeps the valve body hot, expect shortened membrane and seal life.

Two construction details matter for installation. The valve is made as standard for vertical installation; where it must operate horizontally, an extra internal spring has to be used. And the V1617803-0800 version is supplied without a solenoid, in a revolving 90° execution, for arrangements where the pilot is mounted separately. A coupling set (V3592382-0000) is listed for installation.

03Which article number matches which voltage?

The complete valves differ only in the solenoid they carry, so the article number is effectively a voltage code. Read voltage and frequency together: V1617803-0400 is 120 V 60 Hz only — 110 V 50 Hz is V1617803-0300, and 110 V 60 Hz / 100 V 50/60 Hz is V1617803-0200. A solenoid wound for the wrong frequency may still click, but it will not deliver its rated force over time.

Product nameArticle numberPos.
OPTIPOW 105 (24 V DC)V1617803-0100①
OPTIPOW 105 (110 V 60 Hz, 100 V 50/60 Hz)V1617803-0200①
OPTIPOW 105 (110 V 50 Hz)V1617803-0300①
OPTIPOW 105 (120 V 60 Hz)V1617803-0400①
OPTIPOW 105 (220 V 50 Hz)V1617803-0500①
OPTIPOW 105 (UR-CERTIFIED 120 V 60 Hz)V1617803-0600①
OPTIPOW 105 (without solenoid, revolving 90°)V1617803-0800—
Coupling SetV3592382-0000—

04Do you need a whole valve — or just one wear part?

In many cases the valve body is still sound and only one wear part has reached the end of its life. The parts sheet therefore lists every component by position number. The membrane V4549902-0100 (Pos. 2) is the most frequently renewed item; notably, the same membrane is used in both the OPTIPOW 105 (V1617803 series) and the OPTIPOW 135 (V1614718 series). Solenoid valves (Pos. 9) follow the same voltage logic as the complete valves in Section 03.

Spare partArticle numberPos.
MembraneV4549902-0100②
O-Ring (Fluor rubber 64.5 × 3.1)8003-5573③
O-Ring (Nitrile 70SH 64.5 × 3.1)2136-1422③
O-Ring (114.5 × 3.1)2136-1435④
Pilot CoverV3630501-0100⑤
PlateV3630524-0100⑥
PlungerV3630527-0100⑦
Round Washer (SS3576-10-200HV FE/ZN45)4903-2173—
Rubber DiscV3630530-0100⑧
Rubber DiscV3640661-0100⑧
Solenoid Valve (24 V DC)V3611471-0100⑨
Solenoid Valve (100 V, 60 Hz)V3611471-0201⑨
Solenoid Valve (110 V, 50 Hz)V3611471-0300⑨
Solenoid Valve (110 V, 60 Hz)V3611471-0200⑨
Solenoid Valve (120 V, 60 Hz)V3611471-0400⑨
Solenoid Valve (120 V, 60 Hz — UL CERTIFIED)V3640645-0200⑨
Solenoid Valve (230 V, 50 Hz)V3611471-0500⑨

05In which systems does this valve type operate?

The OPTIPOW 105 was designed for Optipulse-type fabric filters — pulse-jet baghouses where rows of bags are cleaned in sequence, in continuous high-load service. Typical installations include:

  • Thermal power — boiler and ash-handling fabric filters

  • Cement & minerals — raw mill, kiln and packing-plant baghouses

  • Glass plants — furnace and batch-house dust collection

  • Mining, metallurgy & steel — sinter, foundry and furnace collectors

  • Production workshops — process dust and powder handling

06How can you tell which part has failed — before opening the valve?

A short diagnostic sequence saves unnecessary disassembly. Work from the signal side towards the air side:

  • Step 1 — Is the signal reaching the valve? If the controller output is present but the solenoid (Pos. 9) does not respond, the fault is electrical or in the pilot stage — not in the main valve.

  • Step 2 — Does the pilot respond but the pulse stay weak? The pilot is venting, but the main stage is not following: suspect a stiffened or torn membrane (Pos. 2) or a sluggish plunger (Pos. 7).

  • Step 3 — Is air escaping between pulses? Continuous venting points to sealing: membrane seating, O-rings (Pos. 3 / 4) or the rubber disc (Pos. 8).

  • Step 4 — Did the problem appear right after a parts change? Recheck identification first — a solenoid of the wrong voltage/frequency (see Section 03) or the wrong O-ring material at Pos. 3 can mimic a valve failure.

Only when these checks point inside the valve does it make sense to open it — and then the position numbers in Section 04 identify exactly what you are looking at.

07Technical questions, answered

Why does differential pressure rise even though the cleaning timer still fires on schedule?

Because the timer only proves a signal was sent, not that a full pulse was delivered. A stiffened membrane, a slow plunger or a partially venting pilot all reduce the effective pulse while the sequence looks normal electrically. Check the pulse quality at the valve (Section 06) before changing timer settings or blaming the bags.

How do you distinguish a membrane failure from a solenoid failure?

Listen and observe at the valve. No click and no pilot venting when the signal fires points to the solenoid valve (Pos. 9). A clear pilot response followed by a weak main pulse, or air bleeding between pulses, points to the membrane (Pos. 2) and its seals. The two faults need different parts — identifying which one you have avoids replacing both by guesswork.

Why must voltage and frequency match — isn't 110 V close enough to 120 V?

No. The article numbers separate them deliberately: V1617803-0300 is 110 V 50 Hz, V1617803-0400 is 120 V 60 Hz only, and V1617803-0200 covers 110 V 60 Hz / 100 V 50/60 Hz. Solenoid force and heating depend on both voltage and frequency; a near-match can work on the bench and still fail early in service.

Does membrane V4549902-0100 really fit both the OPTIPOW 105 and the OPTIPOW 135?

Yes — per the parts documentation, the same membrane (Pos. 2) is used in the V1617803 series (OPTIPOW 105) and the V1614718 series (OPTIPOW 135). It is a shared wear part across the two valve sizes, which is worth knowing when interpreting a stores list that shows one membrane against two valve types.

Can the valve be mounted horizontally?

The standard execution is for vertical installation. Horizontal operation is possible only with an extra internal spring fitted, so that the plunger returns reliably against gravity in that orientation. If a horizontally mounted valve cleans unevenly, check whether that spring is present before suspecting the membrane or solenoid.


Request a Quote — Reply Within 24 Hours

Send: ① quantity of membranes (and any other Pos. parts) · ② your valve series — V1617803 or V1614718 · ③ destination port / country. A nameplate photo speeds up confirmation.

Email: Yanice@starmachinechina.com · WhatsApp: +86-17852092959 · Standard delivery: 5 days


Online Message